Git Push - Username and password in the remote url

git set username and password for remote
git push origin master with username and password
git remote set-url
gitlab push with username and password
git push with different username
git remove remote
git set username and password global
git push with credentials one line

As I understand password prompt when pushing to github can be avoided by adding the username:password in the remote push url.

https://you:password@github.com/you/example.git

Is this a github specific arrangement or can this format be used (https://username:password@somedomain.org/repo.git) with any git remote?

Is this a github specific arrangement?

It's not Github specific; this is actually Basic HTTP Authentication. The user:password@host trick is a way of specifying the BA credentials in the URL.

...can this format be used (https://username:password@somedomain.org/repo.git) with any git remote?

It works only for remotes that use the HTTP protocol. For SSH remotes you'll have to use SSH Keys instead.

Username and password in command for git push, git push https://username:password@myrepository.biz/file.git --all And the repository parameter can be either a URL or a remote name. git: add a remote url with username and password. / Git / git: add a remote url with username and password. Everytime you push your new code to github or bitbucket you need to enter a username and password. But using this tip you can bypass entering Username and password while pushing codes to github.

A more secured way to authenticate you through GitHub than put your password in the remote URL would be, if you use HTTPS, to generate a new token in this GitHub page and then build your remote URL like this:

https://<username>:<token>@github.com/<username>/<project_name>.git

Git push always asking username and password, git remote set-url origin https://username:password@github.com/repo.git. Just replace the 'username' and 'password' with your credentials. The next time you git fetch, git pull, or git push to the remote repository, you'll be asked for your GitHub username and password. If you have two-factor authentication enabled, you must create a personal access token to use instead of your GitHub password.

You can make your local Git remember the GitHub credentials:

If you're cloning GitHub repositories using HTTPS, you can use a credential helper to tell Git to remember your GitHub username and password every time it talks to GitHub.

Chekout this article on GitHub.

Accessing (Pushing to) Github without username and password, to change the url. Switching remote URLs from HTTPS to SSH. Open Terminal ( for Mac and Linux users) or the command prompt (for Windows). The next time you git fetch, git pull, or git push to the remote repository, you'll be asked for your GitHub username and password. If you have two-factor authentication enabled, you must create a personal access token to use instead of your GitHub password.

Git push should not show the password since Git 2.9.3 (August 2016), but, to be on the safe side, Git 2.22 (Q2 2019) improves that even more:

Before, the remote-http transport did not anonymize URLs reported in its error messages at places.

See commit c1284b2 (04 Mar 2019) by Johannes Schindelin (dscho). (Merged by Junio C Hamano -- gitster -- in commit 764bd20, 16 Apr 2019)

curl: anonymize URLs in error messages and warnings

It anonymizes URLs (read: strips them of user names and especially passwords) in user-facing error messages and warnings.


Before Git 2.27 (Q2 2020), error and verbose trace messages from "git push" did not redact credential material embedded in URLs.

See commit d192fa5 (24 Apr 2020) by Johannes Schindelin (dscho). (Merged by Junio C Hamano -- gitster -- in commit 2c42fb7, 01 May 2020)

push: anonymize URLs in error messages and warnings

Signed-off-by: Johannes Schindelin Reviewed-by: Taylor Blau

Just like 47abd85ba0 ("fetch: Strip usernames from url's before storing them", 2009-04-17, Git v1.6.4-rc0 -- merge) and later 882d49ca5c ("push: anonymize URL in status output", 2016-07-13, Git v2.10.0-rc0 -- merge listed in batch #7), and even later c1284b21f243 ("curl: anonymize URLs in error messages and warnings", 2019-03-04, Git v2.22.0-rc0 -- merge listed in batch #5) this change anonymizes URLs (read: strips them of user names and especially passwords) in user-facing error messages and warnings.

Changing a remote's URL, The next time you git fetch , git pull , or git push to the remote repository, you'll be asked for your GitHub username and password. If you have two-factor� Set Username and Password in Remote URL. To save credentials you can clone Git repository by setting a username and password on the command line: $ git clone https:// <USERNAME>: <PASSWORD> @github.com/path/to/repo.git. The username and password will be stored in .git/config file as a part of the remote repository URL.

git-credential-store Documentation, fetch � pull � push � remote � submodule git-credential-store - Helper to store credentials on disk git config credential.helper store $ git push http://example. com/repo.git Username: Each credential is stored on its own line as a URL like: . git remote set-url origin git@github.com:username/repo.git or. Make Git store the username and password and it will never ask for them. git config --global credential.helper store Save the username and password for a session (cache it); git config --global credential.helper cache You can also set a timeout for the above setting; git config

Pushing to remote Git repository from a build, In most cases you can't supply username/password in command line (we are not considering the case when credentials are embedded in repo URL as this is� URL encode your username and password for git, then use it as part of URL itself (when there is no security concern). Say, URL encoded value of username 'user+1' is user%2B1. and URL encoded value of password 'Welcome@1234' is Welcome%401234. Then your GIT Clone URL would look like,

Git - Config Username & Password - Store Credentials, Set Username and Password in Remote URL. To save credentials you can clone Git repository by setting a username and password on the� Encoding the url (especially any special character in a password) is the right solution. The .netrc mentioned below is only for remote repo url, not for the proxy used to resolve said remote repo url. For said encoding, see "Percent-encoding":

Comments
  • The user:password@host pattern is not git-specific; it is Basic HTTP Authentication. I think it does not work on ssh:// git remotes.
  • Thanks @w0lf! Is there any way to automate pushing to remote repository?
  • git push is a command that can be entered in the command line or in scripts. So, yes, you can automate it in any way you like.
  • What I meant was is there a way to automate pushing without prompting for a username and password? Let's say the username and the password is available at the code?
  • I don't know if you can do that. You might want to try using SSH keys instead, if possible.