Installing Windows Service - No mapping between account names and security ID's were done

no mapping between account names and security ids windows 10
icacls no mapping between account names and security ids was done
no mapping between account names and security ids was done local account
0x80070534
no mapping between account names and security ids was done windows service
no mapping between account names and security ids was done chef
performance monitor no mapping between account names and security ids was done
no mapping between account names and security ids was done acronis

I have a windows service and setup project. When I right click on the setup project and click install it prompt me for

  • Username
  • Password
  • Confirm Password

I have tried the following combinations

.\MyUserName MyDomain\MyUserName

but it comes back with the following error

No mapping between account names and security ID's were done

ServiceProcessInstaller

namespace TestService
{
    [RunInstaller(true)]
    public partial class ProjectInstaller : System.Configuration.Install.Installer
    {

        public ProjectInstaller()
        {
            InitializeComponent();

            this.serviceProcessInstaller1.Account = ServiceAccount.User;
            this.serviceProcessInstaller1.Username = @".\MyUserName"; //username;
            this.serviceProcessInstaller1.Password = "123456"; // password;

            // Add installers to collection. Order is not important.
        }

        private void serviceInstaller1_AfterInstall(object sender, InstallEventArgs e)
        {

        }

        private void serviceProcessInstaller1_AfterInstall(object sender, InstallEventArgs e)
        {

        }
    }
}

To be honest, I'm not even sure why I am prompted for a username and password if I set it in the code...

Please cross check whether you have done the following steps (especially step 5):

  1. After creating the windows service project go to the service class's design view(just double click the service1.cs class).

  2. In the design view right click and select Add Installer. This will create an Installer class named ProjectInstaller.cs. With out ProjectInstaller.cs or any error in configuring ProjectInstaller.cs may result in non-showing of the service in service console.

  3. Go to the design view of ProjectInstaller.cs you will find two installers there->

    a.ServiceInstaller1

    b.ServiceProcessInstaller1

  4. Right click ServiceInstaller1 and go to the properties tab

    a.Edit the ServiceName with the name you want to see your service in the service console.

    b.Change the StartType to Automatic.

  5. Right click ServiceProcessInstaller1 and go to the properties tab

    a. Change the account to LocalService

Save and try it.

How to fix error “No mapping between account names and security , How to fix error “No mapping between account names and security IDs” in Active It will be visible in Event viewer > Windows Logs > Application Log To find it need to run command from the domain controller as domain Rights Assignment it shows log on as a service got the faulty account applied. Stack Overflow Public questions Installing Windows Service - No mapping between account names and security ID's were done No mapping between account names and

Your DOMAIN\USERNAME format is correct for a domain, but if you're using a local username, use the computer name for the domain name. If your hostname is FOO and your username is BAR, you'd use FOO\BAR.

You're sure your user account is allowed to escalate, right? It's possible to forbid that via network and local security policy.

Try it with an admin account if it doesn't work.

• View topic, The windows service installer logs information to the following 2 files: HitekService.installlog InstallUtil.installlog. When it fails to install the  Essentially, the reason you are getting the "No mapping between account names and security IDs was done" is because you now have an orphaned user account. This ocurred when you deleted your old user name which was still in use by the system as each user name has a unique SID.

I found a remedy for this situation----however I am using VM WARE cloned 2008 r2's.

Change the SID on the Server 2008 R2 in question using the following steps:

http://www.brajkovic.info/windows-server-2008/windows-server-2008-r2/how-to-change-sid-on-windows-7-and-windows-server-2008-r2-using-sysprep/

This helped me remove the error.

No mapping between account names and security IDs, When installing a windows service, using installutil, it prompted for a username, and password, and since my Administrator user didn't have a  The reason you are getting the "No mapping between account names and security IDs was done" is because you now have an orphaned user account. This occurred when you deleted or renamed your old user name which was still in use by the system as each user name has a unique SID or a corrupted User. You may follow the steps from the article.

Just add the configuration code below in InitializeComponent method installer.

this.serviceProcessInstaller1.Account = System.ServiceProcess.ServiceAccount.LocalSystem;

Fix: No Mapping Between Account Names and Security ID was , Here's how to do it: Press Windows Key + R to open the Run dialog box. Type in regedit to  Which means there is a GPOs setting which used for domain computers, controllers with orphaned account details. Those accounts couldn’t resolved to correct SID. How it is possible? Well there is only two possibilities. 1) The relevant account used in the GPO is removed from AD. 2) Within the GPO the account name is typed incorrectly.

Right click ServiceProcessInstaller1 and go to the properties tab

Change the account to **LocalService**

This worked for me

[RESOLVED] [02/03] Error installing my service with installutil , Win32Exception: No mapping between account names and security IDs was done" Here is the source code for the relevent portion of the  The security ID (SID) that was originally assigned to the domain group is no longer valid. Changing the domain groups that are used for SQL Server 2008 Failover cluster installation is not supported. This is because the security configuration information is set by using the SID of the domain groups that are used during the original setup.

"No mapping between account names and security IDs was done , "No mapping between account names and security IDs was done" error when that are used for SQL Server 2008 Failover cluster installation is not supported. the following error message when you try to start the SQL Server service: Microsoft Visual Studio · Windows Dev Center · Developer Network  The MSI is generated from a VS 2010 setup project for a .NET Windows service targeting .NET Framework 4. My MSI would install fine and the service would start fine when using VS 2005. Only after converting service solution to VS 2010 I started getting the issue. Please guide me.

error 1001 no mapping between account names and security ids , Net windows service targeting .Net Framework 4. My MSI would install fine and the service would start fine when using vs2005. Only after  I saw this in the log: An exception occurred during the Install phase. System.ComponentModel.Win32Exception: No mapping between account names and security IDs was done – user2471435 Feb 6 '14 at 17:32

Error: No mapping between account names and security IDs was done, Error: No mapping between account names and security IDs was done I created a single Windows Server 2008 R2 Service Pack1 image with all the Joining the domain was a breeze and installing SharePoint went great. No Mapping Between Account Names and Security IDs – SQL Server Install and SysPrep Generalize Recently, a colleague and I were working on creating a set of virtual machines to be used in a SharePoint play-pit environment hosted by Hyper-V.

Comments
  • This worked for me, thank you. If I want to configure a more specific user I can always do that after I get the service installed.
  • 5 years later and still a valid answer